Fire Branding Iron Set Stainless Steel 6 0-8 Numbers Cattle Identification

Complete Set of Hot Branding Irons 6 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and won’t burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Brand Design 1. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Animal Health & Veterinary”. The seller is “petsandvet” and is located in this country: US.
  • UPC: 0726287915188
  • EAN: 0726287915188
  • Brand: Keystone
  • Type: Dehorner
  • Model: 55CD
  • MPN: NOT SPECIFIED
Tags: , , , , , , ,
Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Large

Made of heavy gauge steel. The unique design of the burner allows all the irons to heat evenly without regards to positioning of the irons in the heater. Attaches to standard propane tank, not included. Available in 30″ (see other listing) and 15″ lengths. Propane tank & Branding Irons not included. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Animal Health & Veterinary”. The seller is “petsandvet” and is located in this country: US. This item can be shipped to United States.
  • UPC: 0726287915188
  • EAN: 0726287915188
  • Brand: Keystone
  • Type: Dehorner
  • Model: 55CD
  • MPN: NOT SPECIFIED
Tags: , , , , , , , , ,
Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification

Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification. Complete Set of Hot Branding Irons 3 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand (high quality) Stone- The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. Available in several other sizes (see our listings) in 4″, 5″ and 6 BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and won’t burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Brand Design 1. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. Before purchasing any items/product, please insure your country allows this product to be imported. Canceling an Order If you need to cancel an order or make changes, the request must be made within one hour of placing the order and confirmed by an E-Commerce Customer Service Representative. The following rules apply: · Products must be in original packaging and in a new and resalable condition. · Any product that was used or fully/partially installed is non-returnable. Excellent customer service and competitive pricing, is what you will receive when purchasing from Livestock Concepts. We supply a complete line of animal health supplies to livestock producers, veterinarians, pet and equine owners, as well as hobby farmers. We offer over 14,000 items for cattle, swine, sheep, goats horses, pets, birds and exotic animals. We market to 50 states as well as over 60 countries. We provide fast, friendly service, and cherish our customers. Books & Educational Items. Buckets, Tubs & Feeders. Clothing & Boots & Belts. Lawn Garden & BackYard. Pet Equipment & Treats. Rodent & Pest Control. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beef Cattle”. The seller is “livestockconcepts” and is located in this country: US. This item can be shipped worldwide.
  • Brand: L&H
  • MPN: WI-0007843
Tags: , , , , , , ,
Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Small

Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Small. Made of heavy gauge steel. The unique design of the burner allows all the irons to heat evenly without regards to positioning of the irons in the heater. Attaches to standard propane tank, not included. Available in 30″ (see other listing) and 15″ lengths. Propane tank & Branding Irons not included. Before purchasing any items/product, please insure your country allows this product to be imported. Canceling an Order If you need to cancel an order or make changes, the request must be made within one hour of placing the order and confirmed by an E-Commerce Customer Service Representative. The following rules apply: · Products must be in original packaging and in a new and resalable condition. · Any product that was used or fully/partially installed is non-returnable. Excellent customer service and competitive pricing, is what you will receive when purchasing from Livestock Concepts. We supply a complete line of animal health supplies to livestock producers, veterinarians, pet and equine owners, as well as hobby farmers. We offer over 14,000 items for cattle, swine, sheep, goats horses, pets, birds and exotic animals. We market to 50 states as well as over 60 countries. We provide fast, friendly service, and cherish our customers. Books & Educational Items. Buckets, Tubs & Feeders. Clothing & Boots & Belts. Lawn Garden & BackYard. Pet Equipment & Treats. Rodent & Pest Control. The item “Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Small” is in sale since Thursday, November 18, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beef Cattle”. The seller is “livestockconcepts” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: L & H Branding Irons
  • MPN: WI-0007849
Tags: , , , , , , , , ,
Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification

Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification. Complete Set of Hot Branding Irons 3 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand (high quality) Stone- The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. Available in several other sizes (see our listings) in 4″, 5″ and 6 BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and wont burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. Before purchasing any items/product, please insure your country allows this product to be imported. Canceling an Order If you need to cancel an order or make changes, the request must be made within one hour of placing the order and confirmed by an E-Commerce Customer Service Representative. The following rules apply: · Products must be in original packaging and in a new and resalable condition. · Any product that was used or fully/partially installed is non-returnable. Excellent customer service and competitive pricing, is what you will receive when purchasing from Livestock Concepts. We supply a complete line of animal health supplies to livestock producers, veterinarians, pet and equine owners, as well as hobby farmers. We offer over 14,000 items for cattle, swine, sheep, goats horses, pets, birds and exotic animals. We market to 50 states as well as over 60 countries. We provide fast, friendly service, and cherish our customers. Books & Educational Items. Buckets, Tubs & Feeders. Clothing & Boots & Belts. Lawn Garden & BackYard. Pet Equipment & Treats. Rodent & Pest Control. The item “Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification” is in sale since Wednesday, November 24, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beef Cattle”. The seller is “livestockconcepts” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: L&H
  • MPN: WI-0007843
Tags: , , , , , , ,
Fire Branding Iron Set Stainless Steel 6 0-8 Numbers Cattle Identification

Complete Set of Hot Branding Irons 6 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and wont burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. The item “Fire Branding Iron Set Stainless Steel 6 0-8 Numbers Cattle Identification” is in sale since Tuesday, September 14, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Animal Health & Veterinary”. The seller is “petsandvet” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: Stone
  • MPN: 0659
  • Type: Dehorner
  • Model: 55CD
Tags: , , , , , , ,
Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification

Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification. Complete Set of Hot Branding Irons 3 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand (high quality) Stone- The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. Available in several other sizes (see our listings) in 4″, 5″ and 6 BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and wont burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. Before purchasing any items/product, please insure your country allows this product to be imported. Canceling an Order If you need to cancel an order or make changes, the request must be made within one hour of placing the order and confirmed by an E-Commerce Customer Service Representative. The following rules apply: · Products must be in original packaging and in a new and resalable condition. · Any product that was used or fully/partially installed is non-returnable. Excellent customer service and competitive pricing, is what you will receive when purchasing from Livestock Concepts. We supply a complete line of animal health supplies to livestock producers, veterinarians, pet and equine owners, as well as hobby farmers. We offer over 14,000 items for cattle, swine, sheep, goats horses, pets, birds and exotic animals. We market to 50 states as well as over 60 countries. We provide fast, friendly service, and cherish our customers. Books & Educational Items. Buckets, Tubs & Feeders. Clothing & Boots & Belts. Lawn Garden & BackYard. Pet Equipment & Treats. Rodent & Pest Control. The item “Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification” is in sale since Friday, August 27, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beef Cattle”. The seller is “livestockconcepts” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: L&H
  • MPN: WI-0007843
Tags: , , , , , , ,
Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Small

Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Small. Made of heavy gauge steel. The unique design of the burner allows all the irons to heat evenly without regards to positioning of the irons in the heater. Attaches to standard propane tank, not included. Available in 30″ (see other listing) and 15″ lengths. Propane tank & Branding Irons not included. Before purchasing any items/product, please insure your country allows this product to be imported. Canceling an Order If you need to cancel an order or make changes, the request must be made within one hour of placing the order and confirmed by an E-Commerce Customer Service Representative. The following rules apply: · Products must be in original packaging and in a new and resalable condition. · Any product that was used or fully/partially installed is non-returnable. Excellent customer service and competitive pricing, is what you will receive when purchasing from Livestock Concepts. We supply a complete line of animal health supplies to livestock producers, veterinarians, pet and equine owners, as well as hobby farmers. We offer over 14,000 items for cattle, swine, sheep, goats horses, pets, birds and exotic animals. We market to 50 states as well as over 60 countries. We provide fast, friendly service, and cherish our customers. Books & Educational Items. Buckets, Tubs & Feeders. Clothing & Boots & Belts. Lawn Garden & BackYard. Pet Equipment & Treats. Rodent & Pest Control. The item “Hot Fire Branding Iron Propane Furnace Stove Cattle Identification Brand Small” is in sale since Friday, August 20, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beef Cattle”. The seller is “livestockconcepts” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: L & H Branding Irons
  • MPN: WI-0007849
Tags: , , , , , , , , ,
Fire Branding Iron Set Stainless Steel 6 0-8 Numbers Cattle Identification

Complete Set of Hot Branding Irons 6 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and wont burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. The item “Fire Branding Iron Set Stainless Steel 6 0-8 Numbers Cattle Identification” is in sale since Wednesday, June 16, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Animal Health & Veterinary”. The seller is “petsandvet” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: Stone
  • MPN: 0659
  • Type: Dehorner
  • Model: 55CD
Tags: , , , , , , ,
Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification

Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification. Complete Set of Hot Branding Irons 3 Numbers 0-8 (6 is reversed for 9) Stainless Steel Stone Brand (high quality) Stone- The open backed design makes clear legible brands. Precisely formed stainless steel numbers are 3/16″ thick and 1″ deep. Overall length is 36. Available in several other sizes (see our listings) in 4″, 5″ and 6 BRANDING TIPS FOR STAINLESS STEEL FIRE BRANDS A properly applied, legally recorded brand is proof of ownership. It will increase the chance of your recovering stray, missing, or stolen livestock manifold and will serve as a great deterrent to theft as well. A good brand eliminates many markets and outlets where a rustler may dispose of an animal. Heating the Iron Using either a bed of coals or bottled gas, the iron should be heated until it is gray in color. If it is black, it will be too cold and wont burn deep enough. If it is bright cherry red it will burn too deep, possibly leaving a hard sore and a blotched brand. The iron must be hot enough to remove hair and the outer layer of skin. Applying the brand 1. Normally, applying the iron 3-5 seconds will be sufficient to obtain a permanent brand. If the cattle to be branded are carrying extremely long hair, they should be clipped. Be sure to press firmly and rock the iron slightly to get a uniform brand. Do not brand animals that are damp or wet as it will result in scalding rather than burning and in most cases a blotched, slow-healing sore. Restrain the animal to be branded as securely as possible to prevent their moving and causing a blotched brand. Do not brand over an existing brand. Id necessary, place your brand in front, behind, above or below an existing brand but as close as possible to your registered location as possible. There should be only one application of the iron. If it is necessary to retouch the brand, do so with extreme care to avoid blotching. A properly applied brand should be the color of saddle leather when the iron is removed. Care of the Irons 1. Keep your irons free of carbon buildup caused by scale and burnt hair. A bucket of sand or a wire brush at the branding table will aid you in this chore. When you are through branding, the irons should be cleaned and reshaped by using a file or rasp and then be stored in a container of oil. Your brand should be as simple as possible. Avoid intricate patterns which produce sharp corners, as a concentration of heat will cause the brand to burn out and blotch. Sharp edges should be avoided or filed off. Do not use thin or burned-up irons as they will cut deep into the hide and leave a thin scar which will cover with hair. Before purchasing any items/product, please insure your country allows this product to be imported. Canceling an Order If you need to cancel an order or make changes, the request must be made within one hour of placing the order and confirmed by an E-Commerce Customer Service Representative. The following rules apply: · Products must be in original packaging and in a new and resalable condition. · Any product that was used or fully/partially installed is non-returnable. Excellent customer service and competitive pricing, is what you will receive when purchasing from Livestock Concepts. We supply a complete line of animal health supplies to livestock producers, veterinarians, pet and equine owners, as well as hobby farmers. We offer over 14,000 items for cattle, swine, sheep, goats horses, pets, birds and exotic animals. We market to 50 states as well as over 60 countries. We provide fast, friendly service, and cherish our customers. Books & Educational Items. Buckets, Tubs & Feeders. Clothing & Boots & Belts. Lawn Garden & BackYard. Pet Equipment & Treats. Rodent & Pest Control. The item “Fire Branding Iron Set Stainless Steel 3 0-8 Numbers Cattle Identification” is in sale since Tuesday, April 20, 2021. This item is in the category “Business & Industrial\Agriculture & Forestry\Livestock Supplies\Beef Cattle”. The seller is “livestockconcepts” and is located in Hawarden, Iowa. This item can be shipped worldwide.
  • Brand: L&H
  • MPN: WI-0007843
Tags: , , , , , , ,